Kitchen sink round 2

General chat topics, anything and everything you want or need to discuss
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Kitchen sink round 2

Post by formula400 »

Right, sink started slowly draining again, put some Buster Kitchen Plughole Unblocker https://www.google.co.uk/shopping/produ ... rmr:1,cs:1


Flushed with loads of hot water, now it’s leaking when it’s filled over the plug insert (where my finger is pointing to amd it’s also turning (able to spin)

It’s leaking from the black rubber gasket thing under the sink.

Has the sealant dissolved or what? Does it need a new seal?
Attachments
E6A6454E-48E0-4A4D-8BC6-1BBAAF018AB5.jpeg
E6A6454E-48E0-4A4D-8BC6-1BBAAF018AB5.jpeg (275.22 KiB) Viewed 1173 times
8D9BBDF6-3235-4DE0-85F2-A4EBDBC436DE.jpeg
8D9BBDF6-3235-4DE0-85F2-A4EBDBC436DE.jpeg (121.33 KiB) Viewed 1175 times
CBR650r :mrgreen:
cheb
Posts: 4905
Joined: Tue Mar 17, 2020 6:51 am
Been thanked: 2617 times

Re: Kitchen sink round 2

Post by cheb »

Unscrew the right angle bend at both ends, remove it, and you'll find a screw that will enable to tighten the bit you are pointing at down. That should stop the leak.
demographic
Posts: 3028
Joined: Mon Mar 16, 2020 9:30 pm
Location: Less that 50 miles away from Moscow, but which one?
Has thanked: 1346 times
Been thanked: 1722 times

Re: Kitchen sink round 2

Post by demographic »

Wife sez, check the rubber seal is in the right place and tighten the plug hole up.
You could smear a little silicone sealant on the rubber seal as well.

Hold the underneath and use a large slotted screwdriver to turn the centre part with the two slots in it.

Usually anyway.
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Right what now?
Attachments
8DCAF56B-565B-4AEB-B884-4063139A1F63.jpeg
8DCAF56B-565B-4AEB-B884-4063139A1F63.jpeg (176.34 KiB) Viewed 1160 times
CBR650r :mrgreen:
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

The large rubber things seems to be in the right place, I think, it was not touched before it started leaking 😬😬😬
CBR650r :mrgreen:
Mussels
Posts: 4441
Joined: Mon Mar 16, 2020 9:02 pm
Has thanked: 836 times
Been thanked: 1238 times

Re: Kitchen sink round 2

Post by Mussels »

Don't turn the tap on.
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Right got this off, do I need to add silicon or just clean it
Attachments
A997B944-ABA1-4578-9591-CB0A0DC04DC7.jpeg
A997B944-ABA1-4578-9591-CB0A0DC04DC7.jpeg (190.06 KiB) Viewed 1154 times
CBR650r :mrgreen:
Mussels
Posts: 4441
Joined: Mon Mar 16, 2020 9:02 pm
Has thanked: 836 times
Been thanked: 1238 times

Re: Kitchen sink round 2

Post by Mussels »

It looks to me the bit you need to seal is still attached to the sink waiting to be removed. I'm no plumber so treat my advice with contempt.
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Taken the rubber gasket off, can’t really see any trace of sealant before
Attachments
D6FD9C25-4383-47C0-9AD8-4D4493AC01DA.jpeg
D6FD9C25-4383-47C0-9AD8-4D4493AC01DA.jpeg (265.66 KiB) Viewed 1149 times
CBR650r :mrgreen:
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Mussels wrote: Sat Nov 28, 2020 6:16 pm Don't turn the tap on.
😂😂😂😂😂

Cheers fella
CBR650r :mrgreen:
Mussels
Posts: 4441
Joined: Mon Mar 16, 2020 9:02 pm
Has thanked: 836 times
Been thanked: 1238 times

Re: Kitchen sink round 2

Post by Mussels »

It may just need a clean up and reseating, you probably disturbed it before and broke the seal. The sealant will help if the rubber has aged and doesn't work as well as it should.
I fixed a leaking tap a couple of weeks ago just by descaling the internal bits, you don't always need difficult or expensive remedies.
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Right so I have it a cleaned and removed the gunk, put it back together but it’s still leaking form the circled bit, I’ve used a screwdriver to tighten the bolt that hold the plug in, and still the same,
CBR650r :mrgreen:
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Should I put a bit of silicon around where I have put the yellow line?
Attachments
7D2F7002-1DD6-4C91-97DF-D6783D4F4775.jpeg
7D2F7002-1DD6-4C91-97DF-D6783D4F4775.jpeg (169.83 KiB) Viewed 1138 times
CBR650r :mrgreen:
Mussels
Posts: 4441
Joined: Mon Mar 16, 2020 9:02 pm
Has thanked: 836 times
Been thanked: 1238 times

Re: Kitchen sink round 2

Post by Mussels »

That's what I'd try but I'd only give it 50/50 chance of working.
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

If that fails?
CBR650r :mrgreen:
User avatar
Yorick
Posts: 16737
Joined: Sat Mar 14, 2020 8:20 pm
Location: Paradise
Has thanked: 10265 times
Been thanked: 6886 times

Re: Kitchen sink round 2

Post by Yorick »

formula400 wrote: Sat Nov 28, 2020 6:57 pm If that fails?
Pub :)
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

Yorick wrote: Sat Nov 28, 2020 7:11 pm
formula400 wrote: Sat Nov 28, 2020 6:57 pm If that fails?
Pub :)
they are not open yet :thumbdown:
CBR650r :mrgreen:
Hoonercat
Posts: 703
Joined: Thu Apr 23, 2020 12:23 pm
Has thanked: 340 times
Been thanked: 327 times

Re: Kitchen sink round 2

Post by Hoonercat »

formula400 wrote: Sat Nov 28, 2020 6:27 pm Taken the rubber gasket off, can’t really see any trace of sealant before
Is there rubber missing from the outer ring or is it supposed to be like that?
chillitt
Posts: 214
Joined: Mon Mar 16, 2020 7:53 pm
Location: Gloucesterchestershire
Has thanked: 144 times
Been thanked: 164 times

Re: Kitchen sink round 2

Post by chillitt »

Id put just a smear on both sides of the rubber washer, put it back together do the screw up enough to seat it properly then tighten it up fully once the silicon has set. Dont put any on the metal bit that goes on top. (NB Not a plumber)
User avatar
formula400
Posts: 1732
Joined: Wed Apr 15, 2020 4:14 pm
Location: London
Has thanked: 444 times
Been thanked: 863 times

Re: Kitchen sink round 2

Post by formula400 »

This looks like it melted and deformed, could that be why it’s not tight and letting it leak??
Attachments
0E62516E-640F-46D1-900A-9B44BE4BAF56.jpeg
0E62516E-640F-46D1-900A-9B44BE4BAF56.jpeg (136.55 KiB) Viewed 1108 times
CBR650r :mrgreen: