Kitchen sink round 2
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Kitchen sink round 2
Right, sink started slowly draining again, put some Buster Kitchen Plughole Unblocker https://www.google.co.uk/shopping/produ ... rmr:1,cs:1
Flushed with loads of hot water, now it’s leaking when it’s filled over the plug insert (where my finger is pointing to amd it’s also turning (able to spin)
It’s leaking from the black rubber gasket thing under the sink.
Has the sealant dissolved or what? Does it need a new seal?
Flushed with loads of hot water, now it’s leaking when it’s filled over the plug insert (where my finger is pointing to amd it’s also turning (able to spin)
It’s leaking from the black rubber gasket thing under the sink.
Has the sealant dissolved or what? Does it need a new seal?
- Attachments
-
- E6A6454E-48E0-4A4D-8BC6-1BBAAF018AB5.jpeg (275.22 KiB) Viewed 1176 times
-
- 8D9BBDF6-3235-4DE0-85F2-A4EBDBC436DE.jpeg (121.33 KiB) Viewed 1178 times
CBR650r
-
- Posts: 4905
- Joined: Tue Mar 17, 2020 6:51 am
- Been thanked: 2617 times
Re: Kitchen sink round 2
Unscrew the right angle bend at both ends, remove it, and you'll find a screw that will enable to tighten the bit you are pointing at down. That should stop the leak.
-
- Posts: 3028
- Joined: Mon Mar 16, 2020 9:30 pm
- Location: Less that 50 miles away from Moscow, but which one?
- Has thanked: 1346 times
- Been thanked: 1722 times
Re: Kitchen sink round 2
Wife sez, check the rubber seal is in the right place and tighten the plug hole up.
You could smear a little silicone sealant on the rubber seal as well.
Hold the underneath and use a large slotted screwdriver to turn the centre part with the two slots in it.
Usually anyway.
You could smear a little silicone sealant on the rubber seal as well.
Hold the underneath and use a large slotted screwdriver to turn the centre part with the two slots in it.
Usually anyway.
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
Right what now?
- Attachments
-
- 8DCAF56B-565B-4AEB-B884-4063139A1F63.jpeg (176.34 KiB) Viewed 1163 times
CBR650r
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
The large rubber things seems to be in the right place, I think, it was not touched before it started leaking
CBR650r
-
- Posts: 4441
- Joined: Mon Mar 16, 2020 9:02 pm
- Has thanked: 836 times
- Been thanked: 1238 times
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
Right got this off, do I need to add silicon or just clean it
- Attachments
-
- A997B944-ABA1-4578-9591-CB0A0DC04DC7.jpeg (190.06 KiB) Viewed 1157 times
CBR650r
-
- Posts: 4441
- Joined: Mon Mar 16, 2020 9:02 pm
- Has thanked: 836 times
- Been thanked: 1238 times
Re: Kitchen sink round 2
It looks to me the bit you need to seal is still attached to the sink waiting to be removed. I'm no plumber so treat my advice with contempt.
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
Taken the rubber gasket off, can’t really see any trace of sealant before
- Attachments
-
- D6FD9C25-4383-47C0-9AD8-4D4493AC01DA.jpeg (265.66 KiB) Viewed 1152 times
CBR650r
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
-
- Posts: 4441
- Joined: Mon Mar 16, 2020 9:02 pm
- Has thanked: 836 times
- Been thanked: 1238 times
Re: Kitchen sink round 2
It may just need a clean up and reseating, you probably disturbed it before and broke the seal. The sealant will help if the rubber has aged and doesn't work as well as it should.
I fixed a leaking tap a couple of weeks ago just by descaling the internal bits, you don't always need difficult or expensive remedies.
I fixed a leaking tap a couple of weeks ago just by descaling the internal bits, you don't always need difficult or expensive remedies.
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
Right so I have it a cleaned and removed the gunk, put it back together but it’s still leaking form the circled bit, I’ve used a screwdriver to tighten the bolt that hold the plug in, and still the same,
CBR650r
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
Should I put a bit of silicon around where I have put the yellow line?
- Attachments
-
- 7D2F7002-1DD6-4C91-97DF-D6783D4F4775.jpeg (169.83 KiB) Viewed 1141 times
CBR650r
-
- Posts: 4441
- Joined: Mon Mar 16, 2020 9:02 pm
- Has thanked: 836 times
- Been thanked: 1238 times
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
- Yorick
- Posts: 16737
- Joined: Sat Mar 14, 2020 8:20 pm
- Location: Paradise
- Has thanked: 10265 times
- Been thanked: 6886 times
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
-
- Posts: 703
- Joined: Thu Apr 23, 2020 12:23 pm
- Has thanked: 340 times
- Been thanked: 327 times
Re: Kitchen sink round 2
Is there rubber missing from the outer ring or is it supposed to be like that?formula400 wrote: ↑Sat Nov 28, 2020 6:27 pm Taken the rubber gasket off, can’t really see any trace of sealant before
-
- Posts: 214
- Joined: Mon Mar 16, 2020 7:53 pm
- Location: Gloucesterchestershire
- Has thanked: 144 times
- Been thanked: 164 times
Re: Kitchen sink round 2
Id put just a smear on both sides of the rubber washer, put it back together do the screw up enough to seat it properly then tighten it up fully once the silicon has set. Dont put any on the metal bit that goes on top. (NB Not a plumber)
- formula400
- Posts: 1732
- Joined: Wed Apr 15, 2020 4:14 pm
- Location: London
- Has thanked: 444 times
- Been thanked: 863 times
Re: Kitchen sink round 2
This looks like it melted and deformed, could that be why it’s not tight and letting it leak??
- Attachments
-
- 0E62516E-640F-46D1-900A-9B44BE4BAF56.jpeg (136.55 KiB) Viewed 1111 times
CBR650r