Drilling out the remains of a bolt in a cast iron stove

What non motorbike related things are you doing, making, building, planning or designing
cheb
Posts: 4900
Joined: Tue Mar 17, 2020 6:51 am
Been thanked: 2612 times

Drilling out the remains of a bolt in a cast iron stove

Post by cheb »

I'm rebuilding a Morso Squirrel stove.

First problem is the snapped off bolt for the rear damper pivot. I didn't want to use heat for fear of cracking the cast iron. I know it can take the temperature but the localisation was a worry.

The pimple that is left:

Image

Just enough thread left for a nut and guide. I made the guide ages ago on the lathe, a 3mm hole through an M6 25mm bolt.

Image

Pilot hole, done with a hand held drill as it was too much faff to get the stove under my current small bench drill.

Image

5mm hole, the tapping size for a standard M6 thread:

Image

Tapped and finished:

Image

All that's left to do now are the four bolts on the door, make some blanking plates for the boiler holes, refit the door glass, fit new seals and possibly make an adapter to fit to the existing flue.
User avatar
Count Steer
Posts: 11802
Joined: Mon Jul 19, 2021 4:59 pm
Has thanked: 6375 times
Been thanked: 4746 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by Count Steer »

That's worth renovating. :thumbup: (It looks a bit neglected).
Doubt is not a pleasant condition.
But certainty is an absurd one
.
Voltaire
cheb
Posts: 4900
Joined: Tue Mar 17, 2020 6:51 am
Been thanked: 2612 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by cheb »

It is, there's a great little stove, well made and company still supply spares. It came out of an off grid house up here when they put the electric in. Owned by an eccentric ex-military chap. It cost me a tenner, I was at the tip when it was being disposed off and it wouldn't have fitted in the MX5 so I gave him said tenner to deliver it.

Th great thing about cast iron is that it scrubs up well, looks terrible but it's only surface rust. It's only going to be primped until it's usable and then it will be.
User avatar
ZRX61
Posts: 5157
Joined: Tue Mar 17, 2020 4:05 pm
Location: Solar Blight Valley
Has thanked: 1507 times
Been thanked: 1410 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by ZRX61 »

You need a mag-drill ;)
cheb
Posts: 4900
Joined: Tue Mar 17, 2020 6:51 am
Been thanked: 2612 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by cheb »

The mag drill I have access to is too big.

After much wire brushing and spraying, and a couple more episodes of drilling and tapping I now have this:

Image
User avatar
Count Steer
Posts: 11802
Joined: Mon Jul 19, 2021 4:59 pm
Has thanked: 6375 times
Been thanked: 4746 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by Count Steer »

Nice. :thumbup:

Even nicer for a tenner. :D
Doubt is not a pleasant condition.
But certainty is an absurd one
.
Voltaire
cheb
Posts: 4900
Joined: Tue Mar 17, 2020 6:51 am
Been thanked: 2612 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by cheb »

The parts I needed ran to about £50 I think, a used throat plate and glass and seals. The three pieces of the right hand fire brick were glued back together with stixall or similar, whatever tube was open at the time. It may need a grate later but I'll see what happens when the crusty rust comes off, ditto the ash pan.

One spray can of barbecue paint did all the painting needed.

They are a very well made stove IMO ans spare are easily got. They might have been the best selling stove in the UK at one point.
David
Posts: 2134
Joined: Tue Mar 17, 2020 8:50 am
Location: Top 'o the Worle
Has thanked: 218 times
Been thanked: 689 times

Re: Drilling out the remains of a bolt in a cast iron stove

Post by David »

Usually seen tucked into a corner of the lounge on narrow boats....