Garage stuff.

[mangocrazy]

I shadowfoamed most of the drawers in my main tool chest, but haven't yet named the drawers

Perhaps try something different, like heroes from Greek mythology...?

[Rockburner]

I shadowfoamed most of the drawers in my main tool chest, but haven't yet named the drawers

Perhaps try something different, like heroes from Greek mythology...?

I was thinking of using Disney characters....

[Count Steer]

I shadowfoamed most of the drawers in my main tool chest, but haven't yet named the drawers

Perhaps try something different, like heroes from Greek mythology...?

I was thinking of using Disney characters....

I think it would be nice to go alphabetical using names people don't use any more. Albert, Beryl, Claude, Donald, Eric etc.

[ZRX61]

I shadowfoamed most of the drawers in my main tool chest, but haven't yet named the drawers, still takes me a few goes to find certain things.

With the addition of the Yukon box it puts me over 30 linear feet of wheeled toolboxes. If I were to shadowfoam the socketry, spanners, screwdrivers & pliers etc I'd need to swap out my 41in wide main mechanic box for one of this blokes 20 drawer 9footers.. or at east a 7footer:

(Have the missus hide the credit card before clicking this link, these are the dogs danglies of toolboxes)

https://dragonfiretools.com/mechanic-workbench/

[ZRX61]

Took this down:



From here:



Hung these two at the top:



And now have space to hang a new sign when it arrives in a day or three...

[ZRX61]

and then moved the yellow sign up & put it next to the *Crazy* one

[ZRX61]

Today, still waiting on the one I ordered...

[ZRX61]

New sign arrived..

[ZRX61]

New sign showed up. A bit bigger than I expected, so I need to move the two lower signs in the previous post to make space for this:

[ZRX61]

Latest layout... at least until the other sign shows up tomorrow...

[ZRX61]

I may need an intervention...






(there are two more on the way...)

[ZRX61]

Half-assed the garage cabinet-top bookshelf together with the wrong screws (for now). It will be coming apart sanding/varnish etc, and filling two mis-drilled holes
Checked how many manuals I could get on it... (there's are MANY more, some of which I added since I took the pic).
Decided the space in front of the manuals is going to be the permanent home to my measuring tapes (I must have a dozen).
It will getting proper #8x 1.5in slotted brass c/s screws & finish washers. It will also be attached to the gun/ammo cabinet with some carriage bolts, 1 in each side, 2 along the front & 2 along the rear (maybe more). It overlaps the top of the cabinet by 1in



I REALLY miss not being able to use my table saw for this shit. It would have been so much nicer if I wasn't trying to cut plywood sheet with the wrong blade on a frigging circular saw with the ply resting on a couple of 2x4's laid on the floor. (yeah yeah, bad workman & his tools etc blah blah blah, bugger off)

There's also a full set of '73-'80 900/1000 factory manuals & parts books, a full set of KZ650 & KZ1300 parts books, '81-'85 factory GPz11 manuals & also some factory 650/750 manuals (GPz/KZ etc)... and a full set of '73-'80 900/1000 factory service bulletins etc

[ZRX61]

Buggered about with the bookshelf, it's square now. Won't need the bolts to attach it to the cabinet as it's an interference fit.

[ZRX61]

Looked for some drill bits. Looked in the same drawer for the THIRD time in two days & found them this time. FFS.