Replacement MT 07 disk brake bolts

[formula400]

As above mine are showing signs of looking rank.
What replacements should I go for??? Not going titanium as there £££££, but surly I do t want to replace with Yamaha again

Thanks

[weeksy]

TBH mate at the price they are and the funny shape, i'd pay £1.56 each

BOLT
9010906254
Replaces 90109-064G6

I'd then take the removed set and get them nickel coated for later use.

https://www.fowlersparts.co.uk/parts/65 ... ke-caliper

[formula400]

But won’t those go fury again?????
Or have the been updated to be better?

[weeksy]

But won’t those go fury again?????
Or have the been updated to be better?

Not if you throw a bit of ACF-50 at them maybe ? or even get them coated before fitting.

[formula400]

Are there none that do not need extra work???
I’ve never used ACF50 stuff.

[Skub]

Titanium,the only possible choice for the discerning gentleman.

[formula400]

Titanium,the only possible choice for the discerning gentleman.

Any idea where to find that less than £100 for front and back

[Le_Fromage_Grande]

Titanium,the only possible choice for the discerning gentleman.

Any idea where to find that less than £100 for front and back

They'll seize in the ally wheel and never come out, just buy some new Yamaha ones and keep them clean

[Skub]

Titanium,the only possible choice for the discerning gentleman.

Any idea where to find that less than £100 for front and back

Pack of 5 for £19.65?
https://www.ebay.co.uk/itm/283851537559 ... SwOmBemqse

[Yorick]

A pedant would point out that they're screws

[weeksy]

Titanium,the only possible choice for the discerning gentleman.

Any idea where to find that less than £100 for front and back

Pack of 5 for £19.65?
https://www.ebay.co.uk/itm/283851537559 ... SwOmBemqse

Bad bad Skub.... what about the front ?

[Skub]

Any idea where to find that less than £100 for front and back

Pack of 5 for £19.65?
https://www.ebay.co.uk/itm/283851537559 ... SwOmBemqse

Bad bad Skub.... what about the front ?

Ha!

Are they not all the same on the Yam?

[KungFooBob]

I thought you weren't supposed to use Ti on disc bolts, something to do with shearing.

I'm sure we've had this discussion before, where's Dazzler?

[weeksy]

Pack of 5 for £19.65?
https://www.ebay.co.uk/itm/283851537559 ... SwOmBemqse

Bad bad Skub.... what about the front ?

Ha!

Are they not all the same on the Yam?

In honesty I've not looked at part numbers

[Skub]

Bad bad Skub.... what about the front ?

Ha!

Are they not all the same on the Yam?

In honesty I've not looked at part numbers

https://www.ebay.co.uk/itm/283667580545 ... BM1vPm55xf

[Mr. Dazzle]

where's Dazzler?

Short answer is, bolts (or indeed, screws!) are way more complicated than you think.

I wouldn't put Ti bolts in an ally wheel unless I knew there was all the right prep/treatment/grease (I dunno what they'd actually be in this specific application BTW). I would assume that Yamaha have thought about it properly though so I'd just fit whatever OE is.

There's many an inappropriate application of Ti bolts out there! Also, just 'cause it's fitted to a race bike doesn't make it a good idea. Very, very different usage.

As for Nickel plating - yeah it makes 'em shiny, but have you considered that it would change the required tightening torque?

[formula400]

Fair enough, Yamaha bolts it is with some ACF-50